Loading...
comGaragedoors 2018-02-08T15:03:52+00:00
Strength Durability Security
Provided by Steel-Craft Door Products Ltd. Manufactured in Canada

Barcol is a large distributor of Steel-Craft Door Products, who through years of research and development, has become a leading manufacturer in Commercial and Residential overhead doors.

Our Models

THERM-O-DOR
Learn More
Maximum Strength, Energy Efficiency and Security
X

Therm-O-Dor commercial doors are manufactured from the highest quality Canadian made steel, and are designed from the inside out to ensure maximum strength. Our doors feature a patented mechanical interlock design and heavy-duty hardware.  Together, these features offer industry-leading durability, energy efficiency & security.

  • All Therm-O-Dor commercial doors are corrosion-resistant and feature the highest industry treatments of a zinc base coating and two polyester topcoats.  Twice the efficiency of polystyrene panels.
  • The TD 138 model has a 1-3/8″ thickness of polyurethane insulation, which gives an R-Value of 12.60.
  • The TD 134 model has a 1-3/4″ thickness of polyurethane insulation, which gives an R-Value of 16.04.
  • Our unnecessary warranty covers all Therm-O-Dor commercial doors.

END STILES

  • Single end
  • Double end 17’w

HINGES

  • 14ga single end
  • 11ga single end
  • 14ga double end 17’w+
  • 11ga double end 1000lbs
  • 14ga intermediate

TRACK ROLLERS

  • 2″ 10 ball short stem
  • 3″ 10 ball short stem
  • 2″ 10 ball long stem
  • 3″ 10 ball long stem

SPECIALITY TRACK ROLLERS LONG STEM

  • 2″ nylon sealed bearing
  • 3″ UHMW sealed bearing
  • 3″ rubber sealed bearing
  • 3″ nylong stainless shaft

TOP FIXTURE

  • Standard duty single
  • Standard duty double 17’w+
  • Heavy duty double 1300lbs

BOTTOM CORNER BRACKETS

  • Standard duty
  • Heavy duty 1300lbs
  • Heavy duty fail safe

LOCKS

  • Sidelock
  • Interior barlock
  • Exterior keyed barlock

HANDLES

  • Tub handle
  • PVC hand grip
  • Handle step plate

VISION LITES

  • 23″ x 7″
  • 24″ x 12″
  • 34″ x 16″
  • Fullview aluminum

PASS DOOR EXHAUST PORTS

  • 3″
  • 4″
  • 5″

STRUTTING

  • DASMA PVCP Standard
  • Available to increase wind load capacities

WEATHERSTRIP – bottom

  • 3″ U-type
  • 4″ U-type

WEATHERSTRIP – top

  • 2″ top flap
  • 3″ top flap – 17w+

WEATHERSTRIP – side

  • Steel/vinyl
  • PVC/vinyl

WEATHERSTRIP RETAINER

  • Bottom PVC V
  • Bottom Aluminum L
  • TOP PVC V

GUIDE TYPES

  • Standard lift
  • High lift
  • Vertical lift
  • Low lift double track

GUIDE MOUNTING

  • Bracket mount
  • Angle mount continuous 13ga
  • Angle mount reverse 13ga

TORSION SPRINGS

  • Standard 10,000 cycle
  • Optional increased cycle

TORSION SHAFTS

  • 14ga galvanized tube 1″
  • Cold roll solid shaft 1″
  • Cold roll solid shaft 1-1/4

TORSION SHAFT BEARINGS

  • Standard flange bearing 1″
  • Heavy duty flange bearing 1″
  • 2 bolt cast flange bearing 1″
  • Center plate flange bearing 1-1/4
  • End plate flange bearing 1-1/4
  • 2 bolt cast flange bearing 1-1/4

TORSION BEARING PLATES

(engineered for specific weight requirements)

Optional upgrades to components that are connected to the door face.
  1. Graduated End Hinge – available in increased gauge.
  2. Graduated Double End Hinge – available in increased gauge.
  3. Track Rollers – available in a variety of formats to meet your specifications.
  4. Top Fixtures – available in increased gauge.
  5. Low Lift Hardware
  6. Bottom Corner Bracket – available in increased gauge.
  7. Failsafe Bottom Corner Bracket
  8. Locks – 2 point interior, 2 point exterior.
  9. Lift Handle – 3 options available.
  10. Vision Lite Windows – sealed glass: 23″x7″; 24″x12″; 34″x16″; consult your dealer on the wide variety of glass options.
  11. Aluminum – available in full view section; consult your dealer about insert options (glass, polycarbonate – double or triple wall).
  12. Pass Door
  13. Exhaust Ports – available in various sizes.
  14. Strutting – to increase wind load capacity.
  15. Aluminum L Retainer
  16. Specialty High Moisture Area Conversions
  17. Increased Gauge Section Face
Optional upgrades to components that are related to the door guide. All lifts are available in 2″ or 3″ track.
  1. High Lift – track and hardware that causes the door to rise vertically some distance above the top of the door opening before it levels out into a horizontal position. Available to meet a variety of height specifications.
  2. Vertical Lift – track and hardware that causes the door to open vertically where no horizontal tracks are required. Available to meet all height specifications.
  3. Low Lift Double Track – low headroom accessories which enable a door system to operate in minimal headroom conditions. Available to meet a variety of low headroom specifications.
  4. Moveable Center Posts
  5. Full Angle Mount – available in Continuous and Reverse (1″ overlap).
Optional upgrades to components that are related to the door lift.
  1. Torsion Spring Assembly – extensive cycle options are available to meet all specifications.
  2. Torsion Shaft – available in 1″ solid where 1″ tube is specified.
  3. 1-1/4” Solid Shaft
  4. End Bracket – 2-bolt flange bearing, available in 1″ and 1-1/4“.

END STILES

Single end

HINGES

  • 14ga single end
  • 11ga single end
  • 14ga intermediate

TRACK ROLLERS

  • 2″ 10 ball short stem
  • 3″ 10 ball short stem
  • 2″ 10 ball long stem
  • 3″ 10 ball long stem

SPECIALITY TRACK ROLLERS LONG STEM

  • 2″ nylon sealed bearing
  • 3″ UHMW sealed bearing
  • 3″ rubber sealed bearing
  • 3″ nylong stainless shaft

TOP FIXTURE

Standard duty single

BOTTOM CORNER BRACKETS

Standard duty

LOCKS

  • Sidelock
  • Interior barlock
  • Exterior keyed barlock

HANDLES

  • Tub handle
  • PVC hand grip
  • Handle step plate

VISION LITES

  • 23″ x 7″
  • 24″ x 12″
  • 34″ x 16″

EXHAUST PORTS

3″, 4″, 5″

STRUTTING

  • DASMA PVCP Standard
  • Available to increase wind load capacities

WEATHERSTRIP – bottom

  • 3″ U-type
  • 4″ U-type

WEATHERSTRIP – top

2″ top flap

WEATHERSTRIP – side

  • Steel/vinyl
  • PVC/vinyl

WEATHERSTRIP RETAINER

  • Bottom PVC V
  • TOP PVC V

GUIDE TYPES

  • Standard lift
  • High lift
  • Vertical lift
  • Low lift double track

GUIDE MOUNTING

  • Bracket mount
  • Angle mount continuous 13ga
  • Angle mount reverse 13ga

TORSION SPRINGS

  • Standard 10,000 cycle
  • Optional increased cycle

TORSION SHAFTS

  • 14ga galvanized tube 1″
  • Cold roll solid shaft 1″

TORSION SHAFT BEARINGS

  • Standard flange bearing 1″
  • 2 bolt cast flange bearing 1″

TORSION BEARING PLATES

(engineered for specific weight requirements)

Optional upgrades to components that are connected to the door face.
  1. Graduated End Hinge – available in increased gauge.
  2. Track Rollers – available in a variety of formats to meet your specifications.
  3. Low Lift Hardware
  4. Locks – 2 point interior, 2 point exterior.
  5. Lift Handle – 3 options available.
  6. Vision Lite Windows – sealed glass: 23″x7″; 24″x12″; 34″x16″; consult your dealer on the wide variety of glass options.
  7. Exhaust Ports – available in various sizes.
  8. Strutting – to increase wind load capacity.
  9. Specialty High Moisture Area Conversions
Optional upgrades to components that are related to the door guide. All lifts are available in 2″ or 3″ track.
  1. High Lift – track and hardware that causes the door to rise vertically some distance above the top of the door opening before it levels out into a horizontal position. Available to meet a variety of height specifications.
  2. Vertical Lift – track and hardware that causes the door to open vertically where no horizontal tracks are required. Available to meet all height specifications.
  3. Low Lift Double Track – low headroom accessories which enable a door system to operate in minimal headroom conditions. Available to meet a variety of low headroom specifications.
  4. Full Angle Mount – available in Continuous and Reverse (1″ overlap).
Optional upgrades to components that are related to the door lift.
  1. Torsion Spring Assembly – extensive cycle options are available to meet all specifications.
  2. Torsion Shaft – available in 1″ solid where 1″ tube is specified.
  3. End Bracket – 2-bolt flange bearing, available in 1″ and 1-1/4“.

THERM-O-DOR TD134/TD138

WARRANTY INFORMATION

THERM-O-DOR INSTALL MANUAL

TD134 STANDARD LIFT

TD134 HI-LIFT

TD134 FULL VERTICAL LIFT

TD134 SECTION VIEW

TD134-20Ga SECTION VIEW

TD138 SECTION VIEW

SA6000
Learn More
Leading Edge Aluminum Design
X

Aluminum SA6000 overhead doors mix smart design with lightweight construction. The SA6000 design has no vertical stiles, so sightlines are clean and the look is contemporary. Our Lexan lites deliver maximum visibility and high light transmission, helping to brighten large shops and work bays.

Custom extruded rails and stiles ensure structural integrity. Our leading-edge manufacturing processes add further strength. Intermediate and bottom vinyl weather stripping and rails assist our doors to function well under harsh conditions.

sa6000 cross section
The SA6000 comes in a variety of colours, and a full selection of custom paint colours are available. Lexan lites come in five colours to ensure you get the look you desire. Our unnecessary warranty covers all aluminum overhead doors.

STANDARD DOOR SIZE

The SA6000 comes in standard heights and widths from 8′ H x 6′ W up to 20′ H x 18′ W

ANODIZED ALUMINUM

Clear

DURANAR FINISH

Black

White

Additional custom anodizing colours are available. Please contact us for details.

PAINTING COLOUR OPTIONS

A full selection of custom paint coulours are available (special order)

VISION LITE OPTIONS

Thermoclear® Polycarboate Available in triple wall 16mm. Colour options include Clear, Bronze, Blue, Charcoal and White Opal.

Clear Lexan

Bronze Lexan

Blue Lexan

Charcoal Lexan

White Opal Lexan

Note: The glazing material (Lexan) used is ideal for humid environments, however it differs from glass in that it’s not sealed, therefore condensation may form in the cellular walls when interior/exterior temperatures are such that dew point temperatures are created (usually in periods of cooler weather). This condensation usually disappears when warmer weather returns.
The Aluminum SA6000 door features leading edge design elements combined with extremely lightweight construction. Full view sections featuring Thermoclear® with no visible vertical stiles delivers a clean look, with maximum visibility and high light transmission.
Constructed from 45mm (1-3/4“) thick 6063-T5 aluminum alloy.

Frame

Material thickness of top rail, bottom rail and end stile 1.8mm (0.071″) to 2.5mm (0.100″). Thickness at fastener locations 3.2mm (1/8“) or more. End stile widths 76mm (3”) interior, 53mm (2-3/32“) exterior. Top rail height 45mm (1-3/4“) overall. Bottom rail height 43mm (1-11/16“) overall. Combined height of top and bottom rails 87mm (3-7/16“). The top rail of every section to have an integral aluminum strut 38mm (1-1/2“) deep. Top and bottom rails are screwed to the end and intermediate stiles with plated countersunk screws. The screws are located at the section interface and are not visible from the interior or the exterior. Intermediate stiles located on interior face only. Material thickness 1.6mm (0.063″) minimum 4.8mm (0.188″) at fastener locations. Stile width 76mm (3”).

Finish

Anodizing applied to AAMA 611, 607, 608 standards. Painted products (special order) painted to AAMA 2603 standards.

Polycarbonate Insert Panel

Lexan® Thermoclear® triple wall 16mm (3TS) manufactured by GE Structured Products. One single 16mm (5/8“) thick sheet per section set into 32mm (1-1/4“) deep pockets in aluminum frame with waterproof sealant. R value of polycarbonate panel 2.38. U value 0.42. Available in clear, bronze, blue, red and green tints.

Track

50mm (2″) or 75mm (3″) Z275 (G90) galvanized steel. Material thickness 1.9mm (0.075″) for 50mm track and 2.7mm (0.106″) for 75mm track. Vertical tracks to have a graduated slope. Vertical tracks to be bracket mounted 2.7mm (0.106″) or continuous angle mounted 2.4mm (0.093″) and fully adjustable. (Note: reversed angle / 1.0″ overlap not available). Horizontal track to be adequately reinforced per door size and weight.

Door Face Hardware

Graduated end hinges and centre hinges Z275 (G90) galvanized steel. Heavy duty rollers with hardened inner and outer races with 10 grade 500 ball bearings.

Strutting

Integral 38mm (1-1/2“) deep strut on each top rail.

Counterbalance System

Class II Oil Tempered ASTMA229 wire minimum 10,000 cycle torsion springs on continuous steel shaft (solid or tubular shaft as required by size and operation). Aircraft quality galvanized lift cables with a minimum safety factor of 5 to 1.

Locking

Interior mounted slide lock suitable for pad locking.

Bottom Weatherstrip

U type arctic grade vinyl fits into integral bottom retainer.

Section Interface Weatherstrip

Artic grade vinyl bubble shapped weatherstrip at all section meeting rails in integral retainer.

Jamb Mounted Weatherstrip

Anodized or painted aluminum with two point flexible arctic grade vinyl weatherstrip.

Header Mounted Weatherstrip

Anodized or painted aluminum with two point flexible arctic grade vinyl weatherstrip.

Operation

Manual-Standard. Optional: Hand chain hoist (3-1 ratio) or optional electric operator.

Available Sizes

Widths to 6150mm (20’2″) and heights to 5540mm (18’0″)

ALUMINUM SA6000/SA7000

SA6000 SECTION DETAIL

ALUMINUM MODELS SA600/SA7000 WARRANTY INFORMATION

SA7000
Learn More
Advanced Aluminum Construction and Performance
X

The Aluminum SA7000 door is designed for years of reliable operation. Constructed from tough, corrosion-resistant aluminum, this door can become what you need it to be. Create a secure, all aluminum door for increased protection, or add lite panels to create a bright, airy showcase with plenty of curb appeal.

Custom extruded rails and stiles create strong doors, and our leading-edge manufacturing processes add further integrity. Intermediate, bottom and perimeter vinyl weather stripping means our doors function efficiently in all seasons.

sa7000 cross section
This design-friendly door has a wide variety of colour options and custom colours, if desired. Several lite types are available – glass, acrylic or Lexan. Steel insulated aluminum pre-paint insulated panel sections are also available.

STANDARD DOOR SIZE

The SA7000 comes in standard heights and widths from 8’H x 6’W up to 24’H x 28’W

SA700 COLOUR OPTIONS

Anodized Aluminum

Duranar Black

Duranar White

Charcoal

Bronze

Sabel Grey

* Custom powder-coat colours are available upon request. Please contact us for details.

VISION LITE OPTIONS

Maximum thickness 5/8” (16mm) Glass Available in single pane and thermo sealed units. Glass options include Clear, Tempered, Georgian Polished Wire, Satin Texture and Laminated. Glass thickness available in 3mm and 6mm. Arcrylic Available in clear sheet only – 3mm and 6mm single pane. Lexan available in clear sheet only – 3mm and 6mm single pane. Lexan Thermoclear® Available in double wall 6mm or triple wall 16mm. Colour options include Clear, Bronze, Blue, Charcoal, and White Opal.

Clear Lexan

Bronze Lexan

Blue Lexan

Charcoal Lexan

White Opal Lexan

Note: The glazing material (Lexan Thermoclear®) is ideal for humid environments, however it differs from glass in that it’s not sealed, therefore condensation may form in the cellular walls when interior/exterior temperatures are such that dew point temperatures are created (usually in periods of cooler weather). This condensation usually disappears when warmer weather returns.

INSERT PANEL OPTIONS

Full aluminum insert panels are available in anodized and painted colurs. Also available in kick-proof design with insulated core.
The Steel-Craft Aluminum SA7000 door offers significant advancements in product quality and performance. The SA7000 is constructed from the toughest corrosion resistant aluminum and designed for years of reliable operation. The distinctive look will add visual quality and character in a wide variety of applications.
Constructed from 45mm (1-3/4“) thick 6063-T5 aluminum alloy.

Frame

Material thickness of top rail, bottom rail, end stiles and intermediate stiles 1.8mm (0.071″) (3mm (1/8“) at fastener locations). Top rail height 44mm (1-3/4“) overall. Bottom rail height 50mm (2”) overall. Combined height of meeting rails 94mm (3-3/4“). Intermediate stiles 60mm (2-3/8“) wide. End stiles 100mm (3-15/16“) wide. Bottom rail of bottom section and top rail of top section 100mm (3-15/16“) wide. Framework to provide 16mm wide glazing shelf. Optional double end stile with matching bottom-most rail 162mm (6-3/8“) wide. Material thickness of double end stile/bottom rail 0.100” (3mm (1/8“) at fastener locations).

Aluminum Insert Panel

5005 H34 13mm (0.051″) thick aluminum sheet material sealed to door frame with glazing compound and held fast with rigid PVC snap-in mouldings. Painted products (special order) painted to AAMA 2603 standards.

Finish

Anodizing applied to AAMA 611, 607, 608 standards. Painted products (special order) painted to AAMA 2603 standards.

Glazing

Any or all sections can accommodate aluminum panels as well as single and sealed glazing materials up to 16mm (5/8“) thickness. Suggested glazing types include 3mm (1/8“) single glass/acrylic/polycarbonate, 6mm (1/4“) single glass/acrylic/polycarbonate, 16mm (5/8“) sealed glass/Thermoclear® etc. Note: Sealed acrylic or polycarbonate not available. Glass materials to be set on two rubber blocks on bottom edge to absorb impact as door closes. All glazing materials sealed to door frame with glazing compound and held securely with rigid PVC snap-in mouldings.

Track

50mm (2″) or 75mm (3″) Z275 (G90) galvanized steel. Material thickness 1.9mm (0.075″) for 50mm track and 2.7mm (0.106″) for 75mm track. Vertical tracks to have a graduated slope. Vertical tracks to be bracket mounted 3.4mm (0.135″) or continuous angle mounted 2.2mm (0.087″) and fully adjustable for sealing to door to jamb. Horizontal track to be adequately reinforced per door size and weight.

Door Face Hardware

Graduated roller hinges and centre hinges galvanized steel. Heavy duty rollers with hardened inner and outer races with 10 grade 500 ball bearings.

Strutting

Aluminum 6063-T5 alloy angular shaped 44mm (1-3/4“) deep. Material thickness 3mm (0.118″) at furthest point from door face. Anodizing applied to AAMA 611, 607, 608 standards. Painted product (special order) painted to AAMA 2605, 2604, 2603. Strutting is required for doors 4000mm (13’0”) and over in width.

Counterbalance System

Class II Oil Tempered ASTMA229 wire minimum 10,000 cycle torsion springs on continuous steel shaft (solid or tubular shaft as required by size and operation). Aircraft quality galvanized lift cables with a minimum safety factor of 5 to 1.

Locking

Interior mounted slide lock suitable for pad locking.

Bottom Weatherstrip

U type arctic grade vinyl fits into integral bottom retainer.

Section Interface Weatherstrip

Artic grade vinyl bubble shapped weatherstrip at all section meeting rails in integral retainer.

Jamb Mounted Weatherstrip

Anodized or painted aluminum with two point flexible arctic grade vinyl weatherstrip.

Header Mounted Weatherstrip

Anodized or painted aluminum with two point flexible arctic grade vinyl weatherstrip.

Operation

Manual-Standard. Optional: Hand chain hoist (3-1 ratio) or electric operator recommended for doors over 12’0″ high.

Available Sizes

Widths to 7366mm (24’2″) and heights to 54900mm (18’0″)

ALUMINUM SA6000/SA7000

SA7000 SECTION DETAIL

ALUMINUM MODELS SA600/SA7000 WARRANTY INFORMATION

Our Newest Door
SC Industrial
The Ultimate 2″ Heavy-Duty Steel Sectional Door

STRENGTH, PERFORMANCE AND ENERGY EFFICIENT

Steel-Craft’s SC INDUSTRIAL is engineered to deliver advanced performance in commercial and industrial applications. The SC INDUSTRIAL’S two-inch thick, polyurethane insulated panels have an R-Value of 18.50 that answers the demand for greater thermal efficiency, durability and design flexibility. The SC INDUSTRIAL is the ideal choice for protection against heat or cold for all commercial building applications.

  • TRIPLE PANE SEALED WINDOWS
  • 2.0 INCHES THICK
  • 18.50 R-VALUE
  • AVAILABLE IN WHITE OR ALUMINUM FINISH